TB-3123 · REV C · Technical newsheet

Test & MeasurementDevice profile

EV Scale Puts Tensile Testing Standards Back on the Bench

EVs hit 25% of global new car sales in 2025, pulling tensile testing of harnesses, battery foils and lightweight alloys to the center of production quality control.

By Nathan Brooks4 min read789 words

Features

  • EVs were 25% of global new car sales in 2025, over 20 million vehicles, per IEA's 2026 Global EV Outlook.
  • BloombergNEF projects global EV sales will top 23 million by end of 2026.
  • EV wire harnesses must meet ISO 19642, ISO 6722 and USCAR-21; films follow ASTM D882 and ISO 537-3.
  • EV battery packs average 1,000 pounds, driving lightweight alloys, plastics and polymers tested to ASTM D638/E8/D413 families.
  • Some researchers predict EVs will reach two-thirds of all car sales by 2030.
Tensile Testing for Electric Vehicle Safety, Performance & Reliability
Device photoTensile Testing for Electric Vehicle Safety, Performance & Reliability — DarkoStojanovic / pixabay

Electric vehicles reached 25 percent of all new car sales worldwide in 2025 — more than 20 million vehicles — according to the International Energy Agency's 2026 Global EV Outlook, and every one of them passed through tensile and pull-force testing governed by ISO, ASTM and USCAR standards before reaching a dealership. BloombergNEF's Electric Vehicle Outlook for 2026 projects global EV sales will exceed 23 million by the end of this year. By 2030, some researchers predict EVs will account for two-thirds of all car sales.

That growth in volume turns what was once routine materials validation into a production-floor bottleneck with direct safety consequences. The engineering question facing manufacturers is no longer whether to tensile test, but how to keep operator-to-operator consistency at high volume across a material mix that internal combustion vehicles never required.

Which standards govern EV tensile testing?

Wire harnesses illustrate the difference between EVs and conventional vehicles. EVs carry more varied and more intricate harnesses than gasoline cars, and their wires, cables, crimped terminals and welded terminals must withstand vibration, temperature cycling and related stressors. The governing documents are ISO 19642, ISO 6722 and USCAR-21.

Battery components impose a second layer. Thin films and foils, high-voltage cables, wiring, and pack and cell assemblies fall under various ISO and ASTM standards — for example, ASTM D882 and ISO 537-3 for thin films. A battery pack averages 1,000 pounds, which forces lightweighting everywhere else in the vehicle. That pushes EV makers toward carbon fiber, high-strength steel, aluminum and magnesium, plus more plastics and polymers than standard vehicles use. EV rubber compounds also differ from conventional formulations to handle heavier vehicle weight and stricter electrical insulation requirements.

Each material family carries its own tension standard: ASTM D638 and ISO 527 for plastics, ASTM E8 and ISO 6892-1 for metals, and ASTM D413 and ISO 37 for rubber. The balance manufacturers must strike is exacting — materials must be light enough to protect range, performance and handling while strong enough to survive heavy repeated use and environmental stress.

Where does testing enter the production chain?

Tensile testing runs through the entire manufacturing cycle. R&D teams test candidate materials and screen suppliers before committing to production. During production, tensile tests verify crimps, bonds and welds on the assembly line. Quality control inspectors use the same tests on incoming components and to pass audits.

A typical system comprises a test frame, load cell, control panel and grips. The operator prepares a sample, fixes it between grips attached to the frame and load cell, and sets parameters at the control panel — speed, target end condition and results selection. Current-generation testers bundle software that collects and organizes data into graphs and charts.

What limits accuracy on the bench?

Six factors determine whether a test produces valid data, and each maps to a common failure mode:

  • Machine selection. The frame must have appropriate force capacity, and vertical clearance must comfortably accommodate the sample.
  • Load cell selection. Capacity should match expected force as closely as possible. Oversized cells degrade accuracy on small force measurements; undersized cells risk overload damage.
  • Grip selection. Grips must hold the sample without slippage or breakage. Foils and films need gentle faces such as rubber or smooth metal; hard plastics and composites call for wedge or parallel jaw grips with knurled faces; crimped wire terminals require turret-style grips; unusual geometries may require custom fabrication.
  • Sample preparation. Plastic, rubber and metal samples must be cut to the relevant standard's guidelines — the dog-bone shape is common.
  • Sample alignment. Samples are pulled along a straight axis; misalignment or width mismatch with the grips damages the sample or produces invalid readings.
  • Test speed. The pull rate is set by the governing standard or a company procedure. Pulling too quickly or too slowly skews readings.

Component-specific practice varies. Springs in suspension, brake assemblies, seatbelts and hood hardware are held by hooks or Clevis grips and pulled to failure, with elasticity assessed during the run. Wire harness terminals sit in turret grips while bare and coated wires loop around bollard grips, pulled to break or load, with optional load-hold duration checks. Battery separator films and electrode foils go into pneumatic grips or serrated interlocking jaws for elongation and breaking-point measurement. Plastic connector housings and battery enclosures, cut to dog-bone shape, run in wedge grips to failure. Rubber seals, gaskets, hoses, cable insulation and tires follow the same dog-bone route with elasticity checks.

The open question for purchasing departments is whether installed test capacity — frames, load cell inventories and grip sets matched to this standards list — can scale with a market moving past 23 million vehicles a year.

via iea.blob.core.windows.net (Original)

Filed under

  • tensile-testing
  • electric-vehicles
  • materials-testing
  • load-cells
  • iso-and-astm-standards
Share this article:

More from Nathan Brooks

Nathan Brooks

Show full bio

Staff writer covering people, launches and day-to-day practice in Instruments, test and measurement at Testbench Report.

105 articles

Application notes

« Previous articleNext article »