Technical newsheet

Design EngineeringDevice profile

Five low-power FPGA dev kits add secure boot and always-on control

Five FPGA kits target secure boot, always-on control and edge vision. Stated logic capacity ranges from 36,000 to 220,000 cells, but no board-level power measurements support the low-power ranking.

By Nathan Brooks5 min read972 words

Features

  • Lattice introduced the Mach-N2 LN2-MH-20-EVN in September 2026 with 220,000 logic cells and single-chip boot below 30 ms.
  • The MachXO4 RoT lists under-5-ms boot, 16 Mbit SPI flash and up to 381 I/O pins.
  • The CrossLinkU-NX provides four-lane MIPI CSI-2, 64 Mb HyperRAM, 512 Mb SPI flash and always-on operation.
  • Terasic's $169 DE23-Lite uses a 135,110-logic-element Agilex 3 with 64 MB SDRAM.
  • AMD's $229 SCU35 has 36,000 logic cells, up to 304 I/O and 64 Mbit HyperRAM.
5 of the Lowest-Power FPGA Dev Kits Available Today
Device photo5 of the Lowest-Power FPGA Dev Kits Available Today — Sahand Babali / unsplash

By Nathan Brooks

The five low-power FPGA development kits span 36,000 to 220,000 stated logic cells, with two Lattice boards listing boot times below 30 ms and under 5 ms.

The published specifications contain no measured board-level power figure, common test procedure, supply-voltage condition or ambient temperature. As a result, “lowest power” remains a market description rather than a reproducible ranking; engineers must compare the stated functions before assigning the label a procurement meaning.

What do these boards target?

FPGA boards let engineers test hardware designs before production and prototype embedded or industrial applications without first building production hardware.

The five kits cover distinct prototype environments. Lattice emphasizes secure infrastructure and always-on control, Terasic addresses robotics, logic, video and embedded vision, and AMD concentrates on sensor interfaces and board management for medical, industrial and data-center equipment. Edge AI and camera work center on Lattice’s CrossLinkU-NX and Terasic’s DE23-Lite.

What does the Mach-N2 add?

Lattice introduced the Mach-N2 LN2-MH-20-EVN Evaluation Board in September 2026 for secure network infrastructure, always-on system control and high-speed data-interface prototypes. Its 220,000 system logic cells, 12 Mb embedded memory, LPDDR4 and integrated flash pair programmable control logic with external memory and protected configuration.

  • Connectivity includes 4x PCIe Gen4, a PCIe Gen4 x4 finger edge, two FMC expansion connectors labeled HPC and LPC, a Raspberry Pi MIPI camera connector and 1G Ethernet.
  • The FMC connectors and GPIO breakout support sensor, control and I/O expansion. The board also provides 94 wide-range I/O pins and 153 high-speed differential I/O pins.
  • Integrated non-volatile flash protects the FPGA configuration. Lattice specifies “single-chip boot in < 30 ms,” alongside PUF-based security, user run-time security and CNSA 2.0-compliant post-quantum cryptography with crypto agility on the root-of-trust device.
  • Programming uses Lattice Radiant through Mini USB-B. Reference clock sources, eight DIP switches, three pushbuttons, eight green LEDs, three seven-segment LEDs for configuration, GPIO breakout and configuration jumpers support bring-up and demonstrations.

What does the MachXO4 RoT change?

Lattice positions the MachXO4 RoT Development Board for hardware-management and platform-security prototypes using the MachXO4 RoT FPGA. Its hardened cryptographic engine supports secure boot and hardware-based protection, while 16 Mbit quad-read SPI flash provides external storage. The board suits secure boot, hardware management and low-power industrial control.

  • Up to 2,693 kb of user flash is available with dual boot disabled. Lattice describes “instant-on operation (less than 5-ms boot time)” for low-latency control starts.
  • The FPGA offers up to 381 I/O pins in a 484-ball caBGA package. Raspberry Pi, Arduino, Versa, FX12 and Aardvark headers support expansion, while a GPIO interface connects Arduino and Raspberry Pi boards.
  • USB-B handles device programming and I2C communication. Four-position DIP switches, four pushbuttons and 16 LEDs provide demonstrations, while Lattice Radiant remains the programming environment.

What does the CrossLinkU-NX provide?

Lattice’s CrossLinkU-NX SoM Development Kit targets low-power edge AI, embedded systems, camera interfaces and embedded vision. Its always-on feature supports power efficiency while the CrossLinkU-NX FPGA handles MIPI CSI-2 camera input, a USB 3.1 device interface and digital I/O.

  • A four-lane MIPI CSI-2 receiver uses Soft D-PHY, and a 22-pin Raspberry Pi camera connector accepts the sensor module. The module carries 64 Mb HyperRAM and 512 Mb SPI flash; USB Type-C provides USB aggregation.
  • A carrier card can pair the SoM with a Raspberry Pi CM5, adding 1G Ethernet, microSD storage, GPIO and a USB 3.1 host port. The SoM and carrier include debug connections for firmware bring-up before camera or inference work.

What can the DE23-Lite prototype?

The $169 Terasic DE23-Lite runs an Altera Agilex 3 A3CZ135BB18AE75 FPGA with 135,110 logic elements. The board combines 64 MB SDRAM with 89 Mb of M20K and 1.4 Mb of MLAB embedded memory, 368 18x19 hardware multipliers and an integrated ADC for robotics, digital-logic prototypes, video processing, FPGA edge work and power-efficient embedded vision.

  • A 128 Mb QSPI configuration flash stores the FPGA configuration. HDMI output includes audio.
  • USB Type-C supports programming through USB Blaster III, while GPIO and ADC expansion headers expose the mixed-signal and digital interfaces.
  • Ten LEDs, 10 slide switches, four pushbuttons and six seven-segment displays provide visible test points for digital-interface development.

What does AMD’s SCU35 support?

At $229, AMD’s Spartan UltraScale+ SCU35 Evaluation Kit uses an SU35P FPGA with 36,000 logic cells, up to 304 total I/O and 1.93 Mb of on-chip memory. It targets sensor interfaces, board-management systems and I/O expansion for medical, industrial and data-center equipment.

  • Expansion comprises four Pmod connectors, two MikroE Click ports, one SYZGY high-speed I/O connector, an Arduino Shield interface and two Raspberry Pi HAT interfaces.
  • The kit includes 64 Mbit HyperRAM, 10/100 Ethernet through an RJ-45 connector and power-monitoring devices that track system consumption. Hardware security features support the board-management and platform-security use cases.
  • AMD supports the kit with Vivado and Vitis development tools. The connector set lets engineers evaluate sensors and add peripheral modules without requiring a custom carrier immediately.

Can these kits be ranked by power?

No. The comparison supplies logic counts, memory, I/O, links, boot times and two prices, but no watts, current measurements or operating conditions. The less-than-30-ms Mach-N2 and less-than-5-ms MachXO4 claims concern different devices and cannot rank efficiency.

Before hardware moves into production, must each prototype provide a measured power budget and, where claimed, evidence of CNSA 2.0 compliance?

via latticesemi.com (Original)

Filed under

  • fpga-development-kits
  • secure-boot
  • fpga-prototyping
  • embedded-vision
  • low-power-electronics
Share this article:

More from Nathan Brooks

Nathan Brooks

Show full bio

Staff writer covering people, launches and day-to-day practice in Instruments, test and measurement at Testbench Report.

107 articles

Application notes

« Previous article