TB-1045 · REV A · Technical newsheet

Design EngineeringDevice profile

electronica 2026: 18-Motor Robot Hand, 112-Gb/s Modules Top FPGA Showings

At electronica 2026, FPGAs ran an 18-motor robot hand at 10 kHz, a CPU-free 134.7-fs sensor pipeline, and a 112-Gb/s module standard. Here's what shipped in Munich.

By Amara Osei5 min read939 words

Features

  • Inova, Lattice, and DLR coordinated 18 motors and a 10-sensor tactile array within one 10-kHz control period, under 10 µs latency.
  • Sony IMX901 sensor delivers 16.41 Mpixels at 134.7 fps over four SLVS-EC lanes at 9.504 Gb/s each.
  • oHFM connector-based modules reach 112-Gb/s PAM4 per lane; the spec was announced January 2026.
  • Efinix Titanium spans 35K to 2M logic elements on TSMC 16 nm with RISC-V Sapphire SoC support.
  • Microchip PolarFire MPF300TS offers 300K logic elements with SEU-immune nonvolatile configuration.
8 FPGA Standouts at electronica 2026
Device photo8 FPGA Standouts at electronica 2026 — Surprising_Media / pixabay

An 18-motor humanoid robotic hand closed its motion-control loop inside a single 10-kHz period at electronica 2026, with sensor-to-command latency under 10 µs. That demo, from Inova Semiconductors, Lattice Semiconductor, and the German Aerospace Center (DLR), set the tone for an FPGA show floor built around faster processing and tighter control — spanning 4K vision, edge AI, power protection, and radiation-tolerant aerospace parts.

What drove the robotic hand demo?

The Munich demo pairs Inova's APXpress high-speed networking with Lattice CertusPro-NX and CrossLink-NX FPGAs (field-programmable gate arrays, chips whose logic you configure after manufacture). The network coordinates 18 motors, joint sensors, and a 10-sensor tactile array deterministically. Each motor runs local field-oriented control (a motor-drive method regulating torque via magnetic-field vectors) integrated on an FPGA. A daisy-chain topology cuts wiring and preserves space around the hand's moving joints, while synchronizing motor axes and reducing finger-to-finger timing skew. The CertusPro-NX carries up to 100K logic cells and 7.3 Mb of embedded memory; the CrossLink-NX reaches 39K cells, with selectable link rates of 4 to 32 Gb/s and up to 500 virtual data channels. The takeaway: distributed control beats a fat cable for articulation.

Which boards ease prototyping?

At edge lab LIVE!, Adiuvo Engineering launched its Explorer Board, a USB-C FPGA prototyping platform built on Samtec connectivity. It packs four Pmod connectors on Samtec TSW and SSW series parts plus two HSIO interfaces using QSH and QSE board-to-board connectors, so engineers skip a custom board per experiment. Specs include:

  • AMD Artix UltraScale+ AU7P in an FCVA289 package: 37K LUTs, 75K flip-flops, 216 DSP slices, 3.6 Mb block RAM
  • Four GTH transceivers rated up to 12.5 Gb/s
  • Raspberry Pi RP2040 MCU for power management and selected SYZYGY functions
  • On-board HyperRAM for embedded and MicroBlaze V applications
  • Zmod Scope, Digitizer, and AWG module support; USB-C handles power, programming, and JTAG debugging

One board, many experiments. Sensible.

How fast is sensor-to-FPGA imaging?

Macnica's demonstration moved image data from Sony's IMX901-AMR global-shutter CMOS sensor into a Lattice Avant G/X FPGA without a CPU in the datapath. The IMX901 offers 16.41 Mpixels (8016 × 2048), 134.7 fps at 10-bit output and 91.5 fps at 12-bit, over an SLVS-EC interface (Sony's scalable low-voltage signaling standard) at up to 9.5 Gb/s per lane. The demo ran four lanes at 9.504 Gb/s each, using Macnica's Luminous evaluation kit and SLVS-EC v3.1 receiver IP, with processed video out over HDMI at 1920 × 1080 @ 60p. Programmable logic absorbed the sensor-interface workload outright.

What's new in power protection?

Vishay showed a bidirectional FPGA-based electronic fuse developed with Altera — programmable logic supporting protection where current flows both ways, as in battery systems and advanced power architectures, with potential for fast fault response. Vishay also unveiled a unidirectional, MCU-based eFuse built with NXP. Protection, too, is going programmable.

Can one chip run a robot?

Rutronik introduced an Altera Agilex 5 SoC platform combining ROS 2 integration, 4K camera processing, and deterministic motor control in a single device. The FPGA fabric handles sensor interfacing and camera preprocessing; a containerized ROS 2 stack handles frames; Nios V soft processors and Arm cores run path planning and sensor fusion. The workload split targets high-throughput vision plus predictable real-time motion.

What about aerospace reliability?

Future Electronics demonstrated Microchip's PolarFire Avalanche kit, built on the MPF300TS-FCG484I — 300K logic elements, 20.6 MB embedded memory, 924 math blocks, and SerDes from 250 Mb/s to 12.7 Gb/s. Microchip says PolarFire FPGAs aren't affected by single-event-effect-induced configuration upsets (radiation-flippled configuration bits), since configuration cells are nonvolatile and SEU-immune. The board adds 4-GB DDR3, 64-MB serial flash, Gigabit Ethernet via a VSC8531 PHY, a PAN9420 Wi-Fi module, Arduino headers, mikroBUS, Pmod, FlashPro5, and USB 2.0 UART. Future Electronics supplies BOM and engineering support alongside.

Is modular FPGA hardware standardizing?

Samtec presented interconnects for the Open Harmonized FPGA Module (oHFM) standard, announced January 2026 and making its electronica debut. It defines common form factors in solderable (oHFM.s) and connector-based (oHFM.c) flavors, letting developers keep carrier boards while upgrading modules or switching suppliers. Rates run to 64-Gb/s PAM4 per lane for Size-S and Size-M, and 112 Gb/s for Size-L and Size-XL, on 0.635-mm-pitch connectors with 5- or 10-mm stack heights. Extended-length modules add 20 mm of PCB area. The standard spans FPGA-only and CPU-plus-FPGA designs, entry-level through high-performance SoC FPGAs.

How far does the logic scale?

Efinix rolled out its Titanium portfolio — Titanium, Titanium Edge, and Titanium Transceiver series — in Hall B5, Booth 150. Devices span 35K to 2M logic elements on TSMC 16 nm, using the proprietary Quantum compute fabric built from configurable XLR cells, 10K embedded memory blocks, and 93 to 1,344 DSP blocks (Ti35 through Ti375). The Ti375 supports 1.25 to 16 Gb/s per channel across four four-lane transceiver banks. Titanium pairs with Efinix's RISC-V-based Sapphire SoCs, in soft or hardened form, for combined FPGA acceleration and embedded computing.

From a 10-kHz robot hand to a January-born module standard, the thread is determinism. The question buyers should now ask: does their next carrier board, or their next supply contract, speak oHFM?

via wwwlegacy.vishay.com (Original)

Filed under

  • fpga
  • electronica
  • robotics
  • machine-vision
  • ohfm
Share this article:

More from Amara Osei

Amara Osei

Show full bio

Senior reporter covering people, launches and day-to-day practice in Instruments, test and measurement at Testbench Report.

124 articles

Application notes

« Previous article