TB-7087 · REV C · Technical newsheet

Lab InstrumentationDevice profile

17,000-Aircraft Backlog Reshapes Aerospace Failure Analysis Labs

A 17,000-aircraft backlog pushes aerospace labs toward staged failure analysis: SEM first, PFIB, TEM and XPS only when evidence demands, with automation absorbing routine work.

By Olivia Hart5 min read962 words

Features

  • Global commercial aircraft backlog exceeded 17,000 units for the first time in July 2026 — over twelve years of production at current rates.
  • ADS reports more than five times as many aircraft ordered in July 2026 as in July 2025, with 794 deliveries in the first seven months.
  • ADS chief executive Kevin Craven values the backlog at up to £395 billion to UK industry.
  • Staged workflow spans SEM, EDS, EBSD, PFIB, TEM and XPS, escalating only when evidence requires.
  • Automation of particle analysis and phase mapping reduces operator-to-operator variability in quality control.
When an Aerospace Component Fails, Where Should You Look First?
Device photoWhen an Aerospace Component Fails, Where Should You Look First? — Tama66 / pixabay

The global commercial aircraft backlog passed 17,000 units for the first time in July 2026 — more than twelve years of production at current delivery rates — and the strain now reaches materials laboratories asked to explain component failures faster than ever. The industry's answer, laid out in a recent analysis of aerospace failure analysis practice, is a staged workflow: start with scanning electron microscopy, escalate to advanced techniques only when the evidence requires it, and automate the repeatable steps in between.

What do the numbers say?

ADS data shows an industry far removed from the pandemic years. More than five times as many aircraft were ordered in July 2026 as in July 2025, and manufacturers delivered 794 commercial aircraft in the first seven months of the year. Kevin Craven, chief executive of ADS, said: "With the current backlog worth up to £395 billion to UK industry, these figures underline the importance of maintaining a competitive aerospace ecosystem that can support growth, innovation and exports."

Higher output alone is not the issue. Production growth must coexist with aerospace-grade quality requirements precisely as manufacturers introduce new materials and processes that make characterization harder. Beyond established aluminium, titanium and nickel-based superalloys, laboratories now characterize composites, protective coatings, and materials from newer manufacturing routes.

Why does additive manufacturing complicate the picture?

The FAA identifies qualification of new materials and manufacturing technologies — including additive manufacturing — alongside ageing aircraft and field-failure investigation as key areas of aerospace fatigue and damage-tolerance work. Additive manufacturing concentrates the challenge. It offers freedom over component geometry and material use, but the resulting material contains features at very different length scales: macroscopic balling effects, microscale pores and cracks, and nanoscale precipitates and defects.

Determining whether one of these features caused a failure may force a laboratory to move between scales and techniques rather than rely on a single method. The question becomes not how thoroughly a component can be examined, but which sample areas to examine, what information is needed, and which technique comes next.

How does the workflow follow the evidence?

Scanning electron microscopy (SEM) imaging reveals microstructural features and surface topography that locate areas of interest. Energy dispersive x-ray spectroscopy (EDS) then supplies elemental information from those regions — particularly useful for identifying contamination, inclusions or foreign material.

Consider a failed high-strength low-alloy steel. Combining SEM, EDS and automated particle analysis lets engineers compare foreign material in the failed component with inclusions occurring naturally in the bulk steel, establishing their origin and whether the manufacturing process contributed.

Crystallography adds a further layer. Electron backscatter diffraction (EBSD), integrated to an SEM, reveals grain structure, size and orientation at specific sites — important in aerospace metals, because microstructural changes alter mechanical behavior. When particle characteristics alone cannot explain a strength reduction, EBSD exposes differences in grain structure, orientation and local deformation that may contribute to failure.

When should labs escalate to PFIB and TEM?

Not every failed component needs the heaviest instruments. The critical capability, the analysis argues, is recognizing when conventional SEM evidence has stopped answering the question. Plasma focused ion beam (PFIB) microscopy cuts and images successive cross-sections to build a 3D view of an affected region and expose hidden defects; it also prepares thin, site-specific samples for transmission electron microscopy (TEM), which resolves nanoscale and atomic-scale features including precipitates, defects and interfaces. These methods earn their place when SEM, EDS and EBSD have not fully established the failure mechanism.

What can automation remove from the microscopist's bench?

SEM traditionally depends on an experienced microscopist to select operating conditions, navigate the sample, locate features and decide what warrants further investigation. That expertise remains essential for interpreting unusual failures. But not every workflow step demands new scientific judgement.

Automating repeatable activities — image acquisition, chemical data collection, phase mapping, particle analysis — lets laboratories process more samples while cutting operator-to-operator variability. One new technology combines SEM imaging and EDS with live quantitative elemental mapping and multivariate analysis, merging elemental composition data into chemically distinct phase information. It automatically maps phases across the analyzed area, reporting distribution, composition and area fraction rather than elemental ratios alone, and systematically detects, images, characterizes and classifies populations of inclusions instead of requiring manual inspection of each.

The point is not to remove the microscopist. It is to automate repeatable data acquisition and classification so specialist expertise focuses on interpretation and on deciding where the investigation goes next.

When is the problem only skin deep?

Some investigations turn on chemistry rather than structure. Coatings, oxidation, residues and contamination involve extremely thin surface layers, and X-ray photoelectron spectroscopy (XPS) provides elemental composition and chemical states at the surface. A visibly discolored aluminium component may look like a straightforward cosmetic defect; XPS can compare optically different regions, quantify chemical differences, and establish whether contamination or oxidation is responsible.

Aerospace components rely on coatings to resist corrosion, wear and extreme temperatures, and small changes at the coating-substrate interface can affect long-term behavior. Correlative Imaging and Surface Analysis (CISA) addresses this by combining SEM imaging and EDS elemental analysis with XPS surface chemistry on the same region of interest. One cited example — XPS-Raman-SEM analysis of MoS₂ — revealed increased oxidation in one area, increased Raman peak separation indicating more layers, and varying density of MoS₂ structures between areas.

Failure analysis therefore cannot follow one rigid sequence. A fatigue fracture, a grain-structure problem and a surface-contamination problem may all begin with visual inspection, but the evidence determines the next step. The open question for laboratories scaling with the backlog: can they deploy SEM, EDS, EBSD, PFIB, TEM and XPS at the right moments — and automate the rest — without compromising the quality standards the backlog depends on?

via adsgroup.org.uk (Original)

Filed under

  • failure-analysis
  • scanning-electron-microscopy
  • energy-dispersive-x-ray-spectroscopy
  • electron-backscatter-diffraction
  • laboratory-automation
Share this article:

More from Olivia Hart

Olivia Hart

Show full bio

Market editor covering technology and product news in Instruments, test and measurement at Testbench Report.

97 articles

Application notes

« Previous articleNext article »